Search Results - ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat

       

Search:

Type: Posts; User: ZuluWhiskeyFox

Page 1 of 5 1 2 3 4

Search: Search took 0.12 seconds.

  1. Replies
    29
    Views
    1,393

    The results certainly support your theory.

    The results certainly support your theory.
  2. Replies
    29
    Views
    1,393

    The results speak volumes. Can't argue with them....

    The results speak volumes. Can't argue with them. However, there are ways to limit and even eliminate that torque on your D loop. I'm shooting with a truBall Absolute 360. This release has an...
  3. Replies
    47
    Views
    19,312

    When they start getting to shot up in one area...

    When they start getting to shot up in one area its best to restack. Open it up and move the shot up foam to the top and bottom of the target. There by getting fresh material into the area that gets...
  4. Replies
    47
    Views
    19,312

    Lee County Archers in Fort Meyers Florida uses a...

    Lee County Archers in Fort Meyers Florida uses a lot of targets very similar to this one shown. One small difference. We use steel strapping in place of the threaded rod shown in the pic. Thread the...
  5. Those draw length adjustments are a little on the...

    Those draw length adjustments are a little on the course sided. To fine tune draw length you need to add or remove twists. Secondly, if you were successful at installing the peep in the right place...
  6. It's going to be near impossible to determine if...

    It's going to be near impossible to determine if draw length is correct if you can't draw the bow. Precise peep location require you to draw. Tuning and fitting the bow requires you shoot it. To say...
  7. Replies
    12
    Views
    989

    I have found with the smaller aperture that...

    I have found with the smaller aperture that shooting with the pin at the top or bottom of the sight picture makes very little if any difference. So I just Center the pin in the peep and let fly. I'm...
  8. Replies
    25
    Views
    1,052

    I made myself one similar to this. It works...

    I made myself one similar to this. It works great.
    http://images.tapatalk-cdn.com/15/04/27/e1993aa2ffb58113ec1dbe542e17e47a.jpg
  9. Replies
    3
    Views
    190

    There is a fellow in the area that make them out...

    There is a fellow in the area that make them out of all sorts of materials.
  10. Replies
    15
    Views
    625

    My HC is set so I get about an 1/8" knock high...

    My HC is set so I get about an 1/8" knock high paper tear. To get that it's set as follows:
    - Upper cam is advanced about 3/16"
    - Upper Limb Bolt is turned in about 1 turn more than Lower.
    -...
  11. The string maker is replacing the string under...

    The string maker is replacing the string under warranty. Still wondering if anyone else is having this problem.
  12. Those progressive bifocals will cause you a lot...

    Those progressive bifocals will cause you a lot of grief. I wear the older style flat top bifocals well mine are actually tri-focals. So there are two lines. No issues.
  13. Replies
    39
    Views
    1,346

    Golf... A nice walk spoiled by a little white...

    Golf... A nice walk spoiled by a little white ball.
  14. Anarchy HC String Stops/Dampeners issue

    I have an Anarchy HC 50# that I shoot a lot. In the order of 500 arrows per week. My problem is this. The string serving where it contacts the string stop thingy does not last. This is the second...
  15. I'm not a Mathews owner. However, very recently I...

    I'm not a Mathews owner. However, very recently I have seen two of these that the owners were not happy with theirs. In both case it was from a poor setup. I recognized the problem right off. In...
  16. The string set came from one of highly regarded...

    The string set came from one of highly regarded makers often talked about here on AT. Limb bolts have not moved. I did measure the ATA after about 100 shots. It was right on spec at that time. I have...
  17. Replies
    13
    Views
    472

    I like this idea. A day will come when I have...

    I like this idea. A day will come when I have this on my bow.
  18. I have about 1/4" increase in ATA after 6 months...

    I have about 1/4" increase in ATA after 6 months and some 5000 shots. Cam timing has moved as well. I too am wondering if this normal. Do I add a few twists to everything to get the ata and timing...
  19. Replies
    19
    Views
    913

    [For Sale] Release arrived today.

    Release arrived today.
  20. Replies
    8
    Views
    411

    Thanks iceman. This is crazy. Could they make it...

    Thanks iceman. This is crazy. Could they make it any more messed up.
  21. Replies
    8
    Views
    411

    Classifieds where are they?

    Off topic I know. But for the life of me I can't find anything in this latest version of taptalk here on Archery Talk. The classifieds have eluded me and I can't find them. I also can't seem to find...
  22. Replies
    19
    Views
    913

    [For Sale] PayPal sent.

    PayPal sent.
  23. Replies
    19
    Views
    913

    [For Sale] I'll give you 120 for the absolute 360. Shipped...

    I'll give you 120 for the absolute 360. Shipped to Florida.
  24. [For Sale] Is this release a thumb or pinky release? Is it...

    Is this release a thumb or pinky release? Is it still available?
  25. I bare shaft tuned mine. My bare shafts fly the...

    I bare shaft tuned mine. My bare shafts fly the same as fletched.
  26. Did Bear make target bows in the past?

    I'm shooting in the order of 500 arrows per week. I replaced the factory strings about 8 months ago. The factory strings were crap. I replaced them with Vaportrails. The string and cables are not...
  27. Did Bear make target bows in the past?

    Anarchy HC 48#
    http://tapatalk.imageshack.com/v2/14/12/25/8fc98d0a87505e18e7bef02a2d878da8.jpg
  28. Bear Anarchy HC 27.5 draw 48 # 320 gn 255 fps

    Bear Anarchy HC
    27.5 draw
    48 #
    320 gn
    255 fps
  29. Replies
    132
    Views
    13,825

    That stab is just Pucked up. It's Puckery.

    That stab is just Pucked up. It's Puckery.
  30. Replies
    2
    Views
    242

    Well I figured out that the screws in question on...

    Well I figured out that the screws in question on my Anarchy HC are 6-32 x 3/8. They are probably the same on the Finness.
Results 1 to 30 of 142
Page 1 of 5 1 2 3 4