Search:

Type: Posts; User: nuts&bolts

Page 1 of 34 1 2 3 4

Search: Search took 0.97 seconds.

  1. Replies
    53
    Views
    1,012

    Need a short slider pipe to go around the...

    Need a short slider pipe to go around the 3/4-inch backbone pipe.
  2. Replies
    53
    Views
    1,012

    $20 pipe clamp press. Check DIY section. Pipe...

    $20 pipe clamp press. Check DIY section.

    Pipe clamp. 3/4-inch pipe as backbone. Doubled 2x4 fingers.
    Drill four holes to connect doubled 2x4 finger to clamp head.
    Use 1/4-inch bolts and nuts....
  3. Replies
    17
    Views
    779

    Once you set arrow rest centetshot position so...

    Once you set arrow rest centetshot position so the arrow runs dead straight ahead
    of the bowstring...then proceed with other tuning steps...group tuning your arrow rest
    sideways and vertical to get...
  4. Replies
    17
    Views
    779

    No. This tool sets your arrow rest sideways...

    No. This tool sets your arrow rest sideways STARTING position such that your arrow is pointing
    dead strsight ahead....not arrow pointing crooked left...not arrow pointing
    crooked right.

    You can...
  5. Replies
    2
    Views
    62

    http://www.teamusa.org/usa-archery/events/sanction...

    http://www.teamusa.org/usa-archery/events/sanctioned-tournaments
  6. You don't need that adjustment. Much more...

    You don't need that adjustment.
    Much more expensive recurve risers allow you to SHIFT the limb SIDEWAYS, left to right, for horizontal alignment.
  7. Replies
    17
    Views
    779

    https://www.youtube.com/watch?v=RlJ0p4587pM ...

    https://www.youtube.com/watch?v=RlJ0p4587pM

    Centershot gauge

    3/16th diameter rod (sold in 3 foot lengths)
    Bend the rod to 90 degrees

    3/16th inside diameter rubber o-ring

    5.5 inches on...
  8. ALL olympic risers come with limb bolts, and you...

    ALL olympic risers come with limb bolts, and you adjust TILLER with the limb bolts,
    so if a bow has LIMB bolts, then you can adjust TILLER.
    ...
  9. Replies
    9
    Views
    406

    Short version. I can get you your BULLET hole,...

    Short version.
    I can get you your BULLET hole, with ZERO yoke tuning.
    I leave YOKE tuning for fine tuning LONG range groups.

    BAD left tears at 9 yards, I would fix the BASICS, like form, and...
  10. Replies
    9
    Views
    406

    IF you are right handed. IF you TWIST the yoke...

    IF you are right handed.
    IF you TWIST the yoke legs ENOUGH, so that you twist the top limb tips WAY too much, you COULD derail your bow at full draw, causing a dry fire.

    Yoke tuning to get rid of...
  11. MANY of the drawings are from a book by Ray...

    MANY of the drawings are from a book by Ray Axford....ARCHERY ANATOMY.

    Great book. The pdf file is good...but skips around the much more detailed story in the Archery Anatomy book.
    Archery...
  12. Pic of you at full draw. Head to toe photo. ...

    Pic of you at full draw. Head to toe photo. Arrow dead level in photo.
    Are you right handed?
    Do you use a side rod?
    Pic of your 20 yard group of fletched arrows. Fire a bareshaft as well.
  13. Replies
    58
    Views
    1,798

    So, if you are like YankeeRebel...and shoot a...

    So, if you are like YankeeRebel...and shoot a draw length 2-INCHES too long, if you LEAN BACKWARDS enough,
    you can keep your head/nose pointed mostly north, looking in the same direction as the...
  14. Replies
    58
    Views
    1,798

    As you put a shooter in a 6-inch TOO long draw...

    As you put a shooter in a 6-inch TOO long draw length,
    and they FORCE the string to their nose....

    two things happen, they lean WAY WAY back,
    and they TURN their head more and more NORTHEAST,...
  15. Replies
    58
    Views
    1,798

    Some folks LIKE the bow arm NOT in line with the...

    Some folks LIKE the bow arm NOT in line with the shoulders.

    http://i44.photobucket.com/albums/f16/nutsandbolts2006/Screen%20Shot%202015-04-22%20at%207.53.18%20PM_zps5csq7nnd.jpg

    SOME folks...
  16. Replies
    58
    Views
    1,798

    YOu have it backwards. SWING the bow arm where -...

    YOu have it backwards. SWING the bow arm where - ever you like.
    MOST folks use TOO LONG of a draw length, and then, SWING / ROTATE their HEAD to fit...you know, string on da nose.

    Here is the...
  17. Replies
    58
    Views
    1,798

    So, lets talk about your HEAD rotation. ...

    So, lets talk about your HEAD rotation.

    http://i44.photobucket.com/albums/f16/nutsandbolts2006/Screen%20Shot%202015-04-22%20at%208.23.43%20PM_zpsyrqwlgzk.jpg

    Now, if you are NORMAL range of...
  18. Replies
    58
    Views
    1,798

    YOu have a MUCH to fix, if you want to look more...

    YOu have a MUCH to fix, if you want to look more like Dudley.

    http://i44.photobucket.com/albums/f16/nutsandbolts2006/Screen%20Shot%202015-04-22%20at%208.09.39%20PM_zpst9g4l6fq.jpg

    So, John...
  19. Replies
    58
    Views
    1,798

    Fixed the rotation on ALL of your photos. ...

    Fixed the rotation on ALL of your photos.

    http://i44.photobucket.com/albums/f16/nutsandbolts2006/image_zpsh1g1xndg.jpg
    ...
  20. Replies
    18
    Views
    559

    I went through all the SAME problems, as you...

    I went through all the SAME problems, as you did...with a blade rest.
    Could not get rid of a bareshaft diving down LOW....the equivalent of a TAIL high paper tear.

    The final step, is to try the...
  21. Replies
    18
    Views
    559

    AFTER you flatten the blade angle to 30 degrees...

    AFTER you flatten the blade angle to 30 degrees (you need LESS rebound reaction, so try my paper triangle and MEASURE And SET for 30 degrees)
    AFTER you do the SIDEWAYS bow test, for BLADE rest...
  22. Replies
    18
    Views
    559

    When you get home, do this SIMPLE check for BLADE...

    When you get home, do this SIMPLE check for BLADE rest STARTING height position. TURN your bow sideways. YUP, set you bow onto your KITCHEN table.
    Make sure your TARGET sight is installed. Nock...
  23. Replies
    18
    Views
    559

    Check with detlef and see if his records show you...

    Check with detlef and see if his records show you which blade he sent you.
    MIGHT be a 0.008 thickness...MIGHT be a 0.010 thickness.

    Take a piece of paper and make a RIGHT triangle. ONE leg...
  24. Replies
    18
    Views
    559

    You do not have a TILLER problem. YOu have a...

    You do not have a TILLER problem.
    YOu have a BLADE rest adjusting problem.

    BIG difference.

    Bareshaft diving DOWN is very common with beginners on a blade rest.....NOT beginner shooter, but new...
  25. Replies
    4
    Views
    192

    http://i44.photobucket.com/albums/f16/nutsandbolts...

    http://i44.photobucket.com/albums/f16/nutsandbolts2006/File%20Apr%2021%2011%2051%2052%20AM_zps4ypbasof.jpg

    Posture is FAIR....backbone is leaning backwards slightly away from vertical.

    NOck is...
  26. Replies
    4
    Views
    192

    Bow hand GRIP needs LOTS of work. ROTATE bow...

    Bow hand GRIP needs LOTS of work.

    ROTATE bow hand knuckles to 45 degrees, YES, 45 degrees...the bow hand should be CROOKED.
    ...
  27. Replies
    4
    Views
    192

    1) put on shoes..cuz, unless you ALWAYS shoot...

    1) put on shoes..cuz, unless you ALWAYS shoot barefooted, shoes changes how you stand

    2) get the camera off the floor and use a tripod or a stack of boxes, to get the camera LENS at YOUR shoulder...
  28. Replies
    18
    Views
    559

    You COULD just try both ways and FIGURE it out. ...

    You COULD just try both ways and FIGURE it out.

    When you UNTWIST the control cable, the control cable is LONGER (think UP elevator)
    so, since the bowstring is on the OPPOSITE side of the top...
  29. Replies
    2
    Views
    265

    Right or left handed? Pic of YOU at full...

    Right or left handed?

    Pic of YOU at full draw...head to toe photo, with a LEVEL arrow.

    What distance did you shoot fletched and bare? Got a pic?
  30. Replies
    9
    Views
    257

    If you AIM at a shoulder height bullseye, then,...

    If you AIM at a shoulder height bullseye, then, the arrow NEEDS to fly level, to hit the bullseye.
    A bareshaft is an arrow with ZERO steering control...the bareshaft will fly where-ever the BLADE is...
Results 1 to 30 of 1000
Page 1 of 34 1 2 3 4