Search:

Type: Posts; User: JRHOADES20

Page 1 of 34 1 2 3 4

Search: Search took 0.35 seconds.

  1. Replies
    17
    Views
    351

    If the sight is mounted securely, the sight can't...

    If the sight is mounted securely, the sight can't cause inconsistencies, it could be your form, peep, many other things but not the sight.
  2. Replies
    17
    Views
    351

    It isn't the sight, it's you.

    It isn't the sight, it's you.
  3. Replies
    62
    Views
    1,923

    Call the attorney generals office.

    Call the attorney generals office.
  4. I ordered a custom spot Hogg from s&s archery,...

    I ordered a custom spot Hogg from s&s archery, his website was the only one that let you custom build pin colors and sizes, I had it within a week from spot hogg after ordering.
  5. There is no reason you shouldn't be able to tune...

    There is no reason you shouldn't be able to tune them with same POI at 40-50 yards it's all tuning, and what makes those ODB cams do great if you know what to do. I can shoot fps BH's mech and fixed...
  6. Bad advice, I read an article in one of the bow...

    Bad advice, I read an article in one of the bow hunters magazines and an outfitter required every hunter to aim for the guts, their reasoning the had 100% recovery on gut shot bucks and way less on...
  7. Replies
    27
    Views
    634

    Both are great bows it's a shame you can't shoot...

    Both are great bows it's a shame you can't shoot both before but I understand why you can't. You can't go wrong with either but the OD Binary cams, flex guard on the Bowtech bows are hard to beat...
  8. Replies
    13
    Views
    408

    I've noticed some of their stuff i need a large...

    I've noticed some of their stuff i need a large some xl. They are different fits, some loose,and some form fitting. I agree it is weird. I will not buy UA hunting suits without trying them on. I...
  9. Go spot hogg

    Go spot hogg
  10. Replies
    24
    Views
    757

    I bet when you draw back if someone tried to move...

    I bet when you draw back if someone tried to move your nock they couldn't because the string angle. If it is too much it isn't by much, I like a little room above the tied nocking points , and when...
  11. Replies
    24
    Views
    594

    I do this all the time, works, just drop drill...

    I do this all the time, works, just drop drill bit in with flat part facing towards the insert, and be careful swinging.
  12. Yes you can twist the string a few twists, just...

    Yes you can twist the string a few twists, just don't over do it. 2 twists should be sufficient.
  13. Replies
    26
    Views
    751

    I like it!

    I like it!
  14. Replies
    7
    Views
    187

    In my past Experience a couple twists, i wouldn't...

    In my past Experience a couple twists, i wouldn't go more than 2-3, then add a twist to each cable to get draw weight back. I'd draw weight is low you can just add to cables but if it's near peak...
  15. Replies
    7
    Views
    187

    I'd prob go longer and add a couple twists, don't...

    I'd prob go longer and add a couple twists, don't over do it, might have to twist cables for draw weight after.
  16. Replies
    30
    Views
    775

    Sending prayers!

    Sending prayers!
  17. Replies
    206
    Views
    8,192

    Sounds fair to me it isn't Bowtechs fault you...

    Sounds fair to me it isn't Bowtechs fault you damaged the bow, a release misfiring would stay in your hand, not hit a wall. Your lucky it was only a string.
  18. Replies
    9
    Views
    285

    I agree, move the mods not draw stops. My...

    I agree, move the mods not draw stops. My Experience and CPXL is this way.
  19. My 13' Experience is the first bow I will hunt...

    My 13' Experience is the first bow I will hunt with more than one season in my short hunting career lol.
  20. Replies
    6
    Views
    136

    Yes to start, it is ok to go against the grain,...

    Yes to start, it is ok to go against the grain, set prelean equal while staying in timing dots of cams to start, you will need a draw board obviously. There is no reason the top right yoke should...
  21. Replies
    6
    Views
    136

    Read this whole thread, very informative...

    Read this whole thread, very informative specifically Shane's post #37, this is the exact process I've used and usually have bullet holes in 30-60 minutes.
    ...
  22. Replies
    6
    Views
    136

    You should rough time the cams and set prelean on...

    You should rough time the cams and set prelean on the top and bottom cam so they are equal. Typically you do want to mirror what you do once you get your prelean set if you put 1/2 twist on top...
  23. Replies
    16
    Views
    391

    String issue prob need to twist string a twist or...

    String issue prob need to twist string a twist or untwist a trust, sounds like your dloop isn't synched very good and keeps slipping. Your shop should be able to fix.
  24. Check with a bowtech dealer.

    Check with a bowtech dealer.
  25. Replies
    39
    Views
    1,022

    Shortening it 1/2" can only help her IMO. Might...

    Shortening it 1/2" can only help her IMO. Might feel weird but I'd suggest it.
  26. Replies
    29
    Views
    632

    Tagged

    Tagged
  27. Replies
    12
    Views
    343

    Spot Hogg built like tanks.

    Spot Hogg built like tanks.
  28. Replies
    2
    Views
    161

    On some yes, on some no. The experience seems...

    On some yes, on some no. The experience seems rated under most get more than 335, overdrive some seem to get more than IBO, the 360 some are at or 10 below depending on dl and tune. It just...
  29. Replies
    50
    Views
    2,330

    Just got a 2014 CPXL, no stretching or peep...

    Just got a 2014 CPXL, no stretching or peep twists however I am disappointed in serving desperation on cables and endloops.
  30. Replies
    16
    Views
    575

    Wow that's sharp

    Wow that's sharp
Results 1 to 30 of 1000
Page 1 of 34 1 2 3 4