Search Results - ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat

       

Search:

Type: Posts; User: Huntinsker

Page 1 of 34 1 2 3 4

Search: Search took 0.55 seconds.

  1. Replies
    2
    Views
    47

    Tighten all the screws on it.

    Tighten all the screws on it.
  2. Replies
    6
    Views
    336

    Can't tell much from the pic since we can't see...

    Can't tell much from the pic since we can't see any of your lower body or the bow.

    I've found that changing the DL on a bow to try and bareshaft tune is not very effective. I tried to lengthen my...
  3. Replies
    3
    Views
    134

    Stick with 24 and you'll be good to go assuming...

    Stick with 24 and you'll be good to go assuming you don't use too large of end serving. Most bow manufacturers use basically the same size of string/cable groove on the cams so you can use pretty...
  4. Replies
    17
    Views
    436

    Sounds like you're shooting for score rather than...

    Sounds like you're shooting for score rather than shooting to shoot 60 good shots. If you just focus on making good shots, the arrow will find the middle. If you focus on shooting a certain number,...
  5. Check out page 111, post 2775 and then page 130,...

    Check out page 111, post 2775 and then page 130, post 3244. nestly made some incredible videos showing the relationship between twisting a string and serving a string and what way is correct. When...
  6. Replies
    5
    Views
    274

    I'll try to answer your questions quickly. No...

    I'll try to answer your questions quickly.

    No it's not always like that. The more you do it, the faster you get. You shouldn't install the peep until you shoot the bow about 20-50 times to let...
  7. Read my post above yours. Answer is that it...

    Read my post above yours. Answer is that it depends. I was able to do it on my buddies z7. You may or may not. You'll just have to try. If I were you I'd not worry about your string and cable getting...
  8. Here's my advice. Just try it. Try shortening the...

    Here's my advice. Just try it. Try shortening the cables and severely shortening the string and see if you can find a sweet spot where you'll actually be able to shorten the draw but keep the draw...
  9. If your peep doesn't rotate when you draw the...

    If your peep doesn't rotate when you draw the bow, then you don't have a problem. Unfortunately we can't always get our peep in the perfect position within the twist of the string to get it to sit...
  10. If it were me, I'd serve the loops the way you...

    If it were me, I'd serve the loops the way you want and then secure the tag ends some how. I'd probably do a couple wraps and then back wrap so that they can't get pulled under the serving. It would...
  11. Replies
    41
    Views
    1,155

    Bob Deston who started BCY worked for Brownell...

    Bob Deston who started BCY worked for Brownell before leaving and starting BCY.
  12. I'm no recurve pro but it looks pretty good to...

    I'm no recurve pro but it looks pretty good to me. The only thing that may need some attention is your follow through on the front end. You seem to drop your bow hand down as the arrow is released....
  13. Replies
    46
    Views
    1,375

    It's not giving up on a bow when you purchase...

    It's not giving up on a bow when you purchase another bow. If it were me, I'd have spent the money that you used on the camera and got a bow that you could handle. If you want to learn how to shoot,...
  14. Replies
    12
    Views
    356

    A persistent left tear or nock left bareshaft is...

    A persistent left tear or nock left bareshaft is often caused by having too much pressure on the right edge of your grip, doesn't matter if you're right or left handed. Pushing too hard on the right...
  15. If it were me, I'd move the rest back down and...

    If it were me, I'd move the rest back down and add a twist or two to the cable that attaches to the bottom cam and see if that doesn't do it for ya.
  16. Replies
    46
    Views
    1,375

    No I'm serious. You got your best arrow flight...

    No I'm serious. You got your best arrow flight that way which was obvious by your videos. Without any more description or explanation that what you've give, I think anyone would assume that you meant...
  17. Replies
    46
    Views
    1,375

    I don't think you needed slow motion for someone...

    I don't think you needed slow motion for someone to tell you that you'll get better arrow flight by putting the arrow on the left side of the riser and shooting fingers when shooting right handed....
  18. Replies
    8
    Views
    203

    Adjust your sight and keep shooting, if you...

    Adjust your sight and keep shooting, if you continue to drop low, then it's not the sight or the bow tune but it's something you're doing. If it's fixed by moving the sight, check your tune and make...
  19. Replies
    7
    Views
    276

    3732258

    3732258
  20. Replies
    3
    Views
    109

    I think Antonio Amaral has a sheet from Bear with...

    I think Antonio Amaral has a sheet from Bear with that info on it. Try sending him a pm and see if he'll post that in here again.
  21. Replies
    34
    Views
    1,034

    Remember that dramatic reduction of addictive...

    Remember that dramatic reduction of addictive agents like caffeine and nicotine can cause withdrawal symptoms which may exacerbate your problem. It's best to slowly decrease the use of those products...
  22. Replies
    41
    Views
    1,155

    Same tune?

    Same tune?
  23. Replies
    41
    Views
    1,155

    I don't think you can compare the shot feel of a...

    I don't think you can compare the shot feel of a material using different bows. The bows themselves will feel different so of course one could confuse that difference as the string material.
    ...
  24. Replies
    41
    Views
    1,155

    Nope, never experienced anything like that. I've...

    Nope, never experienced anything like that. I've had Fury on all my bows for 2 years now, both hunting and target, and I've never once had to tweak the cables/strings to get the cam marks lined back...
  25. Replies
    34
    Views
    1,034

    What type of targets are you shooting? Can you...

    What type of targets are you shooting? Can you shoot a blank bale without shaking or does it only happen when you have a dot to shoot at? Have you tried shooting 3d targets without a dot to see if...
  26. Replies
    41
    Views
    1,155

    BCY X is a blended material with Dyneema and...

    BCY X is a blended material with Dyneema and Vectran. Vectran is a very stable material but it does fuzz up. When you hear of someone's strings fuzzing on them, it's typically a vectran blend. 8190f...
  27. If you're paying for that, and they only charge...

    If you're paying for that, and they only charge $16, you better get to a doctor. :wink:
  28. Replies
    13
    Views
    354

    Those are actually pretty thick for how much...

    Those are actually pretty thick for how much you'll need to move the cam. Why did the bow derail on you? Did you not set the top cam lean before drawing the bow? Remember, you need to move a shim...
  29. Replies
    13
    Views
    354

    If it hits then yes. Move the cam to the right a...

    If it hits then yes. Move the cam to the right a very small amount. Move the smallest shim from the right to the left side of the cam and you'll be good to go.
  30. No offence, but you've got to be kidding. One...

    No offence, but you've got to be kidding. One normal bolt weighs about the same as your field point. If you have to get rid of 90 grains off of your bow to make it more comfortable to shoot, you have...
Results 1 to 30 of 1000
Page 1 of 34 1 2 3 4