Search Results - ArcheryTalk Forum: Archery Target, Bowhunting, Classifieds, Chat

       

Search:

Type: Posts; User: Pasinthrough

Page 1 of 34 1 2 3 4

Search: Search took 0.57 seconds.

  1. Replies
    21
    Views
    749

    At 13/16" your arrow should be running straight...

    At 13/16" your arrow should be running straight down the string when viewed from behind. I measure the center shot at the rear and front of the riser to ensure it's the same.

    Again, not all bows...
  2. Replies
    9
    Views
    183

    I would advise doing that and also moving the...

    I would advise doing that and also moving the nock height to where the centre of the arrows crosses the top of the berger holes. That should help you out.
  3. Replies
    9
    Views
    183

    Also check to make sure the launcher is not...

    Also check to make sure the launcher is not slapping the arrow shelf.
  4. Replies
    8
    Views
    251

    Here is a photo of one I got in last month....

    Here is a photo of one I got in last month. http://images.tapatalk-cdn.com/15/06/26/90af568db25a968737e3982a72d0e435.jpg
  5. Replies
    16
    Views
    561

    Easy there pal, I put your order in on June 8th. ...

    Easy there pal, I put your order in on June 8th. This is the end of week 3 and I check on order status every single week and usually several times per week. I have no control over when it will be...
  6. Replies
    3
    Views
    241

    No problem. We'll get this sorted out for you. ...

    No problem. We'll get this sorted out for you. Don't worry.
  7. Replies
    3
    Views
    241

    If the photo from the top has the arrow on the...

    If the photo from the top has the arrow on the rest, then the center shot is way inside. Set the center shot to 13/16" and if you don't get a clean hole through paper, then you will need to have the...
  8. Replies
    13
    Views
    403

    The 2013 Knightmare specs are in this thread: ...

    The 2013 Knightmare specs are in this thread: http://www.archerytalk.com/vb/showthread.php?t=2164979

    The 2015 Knightmare GT specs are here: http://www.obsessionbows.com/knightmare-gt.html
  9. Replies
    9
    Views
    411

    Both will feel super at that draw length. As...

    Both will feel super at that draw length. As stated, the Fusion will be a tad faster and probably be capable of more let off, so it's up to you to choose if you want draw specific or modular. Both...
  10. Replies
    9
    Views
    411

    What draw length and poundage?

    What draw length and poundage?
  11. Replies
    21
    Views
    749

    ^^^^ Stik is correct.

    ^^^^ Stik is correct.
  12. Replies
    21
    Views
    749

    Working on these bows comes pretty easy for me. ...

    Working on these bows comes pretty easy for me. I've been working on these slaved cam systems for 10 years now and while I don't pretend to know everything, I have learned a lot through those years....
  13. Replies
    3
    Views
    217

    The bows shoot great for me without adding...

    The bows shoot great for me without adding anything to them. The grip has imo, gotten better since the 2012 models. Comfy and repeatable without a problem.
  14. Replies
    21
    Views
    749

    I've never had an issue with doing this. Just...

    I've never had an issue with doing this. Just make sure it is secure and don't go pulling or framing around on it and it should be fine. If I ever leave it for more than a couple of minutes, I...
  15. Replies
    2
    Views
    113

    Yes, for 2014. Only exception is the short draw...

    Yes, for 2014. Only exception is the short draw cam and mods.
  16. Replies
    21
    Views
    749

    I'd try swapping them first since there wouldn't...

    I'd try swapping them first since there wouldn't be any cost in it. I'd venture to suggest you'd need something like .165-.175 on the right. Your shims total .340. The average I see is 320-325 so...
  17. Replies
    21
    Views
    749

    It had .160 each side and I ended up with...

    It had .160 each side and I ended up with .145/.175. Just move the cams over slowly and when you get it right, you'll know it asap. Glad you got yours fixed and it's shooting well now.
  18. Replies
    21
    Views
    749

    I'd like to say that doing this is the exception...

    I'd like to say that doing this is the exception rather than the rule for these bows. Most of the ones I setup from the factory tune just fine. Occasionally I'll run into one like I did last night....
  19. Replies
    21
    Views
    749

    Both ends were changed, I just showed one due to...

    Both ends were changed, I just showed one due to keeping the video short as possible.
  20. Replies
    21
    Views
    749

    Shim change out and results video

    I ran into a little problem setting up a Delta 6 last night. When I saw what it was doing, I decided to do a little video showing everyone the way I correct the problem. The process is detailed in...
  21. Replies
    9
    Views
    418

    Get the 14 Evolution and get him to order you 70#...

    Get the 14 Evolution and get him to order you 70# limbs when he's getting your module set. You'll have exactly what you want for less money than new.
  22. Replies
    14
    Views
    588

    That's just where the self-centering attachment...

    That's just where the self-centering attachment ends up. It pulls directly behind the peg where the grip sits. This way the bow doesn't sit at an angle. I've done so many I've lost count and from...
  23. Replies
    14
    Views
    588

    It seems that video has helped a lot of folks. I...

    It seems that video has helped a lot of folks. I hope to have the time to do another one for the 2015 bows soon. Glad you got your bow shooting well.
  24. Replies
    14
    Views
    403

    Remember to play with the speed sleeve placement...

    Remember to play with the speed sleeve placement a little. You can pick up or loose some depending on their location.
  25. Replies
    14
    Views
    403

    Search for Hogwire strings. Rob does a great job...

    Search for Hogwire strings. Rob does a great job and the material he uses is pretty wicked. Fury
  26. Replies
    14
    Views
    326

    Most instances of re-shim are needed due to the...

    Most instances of re-shim are needed due to the draw length or poundage being at the far ends of the spectrum. I end up shimming quite a few bows as I do work for archers of all shapes and sizes. ...
  27. Replies
    17
    Views
    302

    I'd be happy to help, if I can. I've got a parts...

    I'd be happy to help, if I can. I've got a parts order going in today anyway. OP, let me know.
  28. Replies
    17
    Views
    302

    Stikbow is correct. Here is the thread with the...

    Stikbow is correct. Here is the thread with the older models info in it: http://www.archerytalk.com/vb/showthread.php?t=2164979

    The 2013 Knightmare is very different from the Knightmare GT.
  29. Replies
    15
    Views
    540

    Welcome. Enjoy your bow and ask questions if you...

    Welcome. Enjoy your bow and ask questions if you need to. We'll help all we can.
  30. Replies
    21
    Views
    707

    The only problem I've found with the ripcord is...

    The only problem I've found with the ripcord is the location of the windage bolt on the rest body. Due to that location, the cable rod on the bow gets in the way and it's impossible to adjust the...
Results 1 to 30 of 1000
Page 1 of 34 1 2 3 4