February 6th, 2014, 11:26 PM
I for one don't agree with with all your theories - having such a wide d loop will cause more string pinch pressure than a conventional loop without the serving due to the angle that's created with the serving being added and when the serving is unequal you're not drawing directly behind the arrow as you stated - the release will find the center of the loop, which in your case will be low. Not saying what you're doing is wrong - I just don't agree with it ... to each their own
February 20th, 2014, 03:53 PM
Tag for tiring in a nock. Boom!!
Bowtech Experience. Limb driver rest, BStinger, Sword site, black eagle arrows, wasp Broadheads
February 24th, 2014, 11:45 AM
awesome way to do this...i use this method religiously
Addicted String Builder>>>-------->
Obsession Phoenix+reapers=death from above!
Ever seen a U-Haul following a hearse??? Don't Hold Back!
Hi Tek Stabilizers Pro Staff
May 27th, 2014, 08:07 AM
I use just D loop without nock or serving material, Nylon string/cord. Short as possible and set it with D loop pliers, use first c-clip pliers stretching D-Loop and pre set knots, the you can get your D Loop plier pulling the knots tight.
July 21st, 2014, 09:26 PM
Thank you so much for this post! I have been looking for this exact information. This is what makes AT great.
July 28th, 2014, 04:30 PM
tagged for later, very good info.
2013 Bear Encounter LH, QAD HDX, Apex Bone Collector 4 pin, Trophy Ridge 9" Static Stabilizer, TruFire release, GoldTip expedition hunter 7595
July 29th, 2014, 05:28 PM
August 5th, 2014, 09:57 AM
Which way would a right handed shooter tire their d loop to avoid added peep twist? Can someone post a pic?
August 5th, 2014, 01:59 PM
I really don't think this is an issue. You want the hitch knots tied opposite each other. I really feel most problems with D-loops and slipping or twisting is in the quality of the string and if it wants to twist or turn and the way the center serving is placed on the string. With my system the top knot of the D-loop has the larger load, if the serving is wound the wrong way for the shooter, then as the knot resists twisting in can tighten the underlying serve or loosen it. If it loosens it it will separate and loose it grip on the serving.
Originally Posted by NJlungbuster
Little Jon Archery Products
Bowstring Jig and Serving Winders
BCY String Material distributor, Bowstring making and tuning Phone Orders 800-437-9145
August 6th, 2014, 01:42 PM
Bowtech Assassin 72# 28"
August 29th, 2014, 11:08 AM
2009 ALPINE SABRE 65dw, 28dl, 306fps - Tru Ball AXCEL 3000, Sure Loc 35mm Scope - Trophy Taker Micro Spring Steel II - AEP and Xtreme X3 Stab - Rocket Slings - Easton Fatboys - STAN Mag Micro & Carter Hammer
2010 ALPINE ASSAULT
- The SYSTEM sight, Specialty Scope, Trophy Taker Micro Spring Steel I, Paradigam S.O.S 24" stab.
December 11th, 2014, 07:28 PM
I have just used my new tied in nock sets to adjust nock height. Paper tuning and a nock high tear. Jiggle the d loop apart a bit and screw the nock sets down a turn, presto, bullet hole! Thanks Deezlin for the info. Now if mine looked as good but hey, they work.
Hoyt Spyder 34
QAD Ultra Rest HDX
HHA Optimizer Lite
By 60X in forum Arrows & Strings
Last Post: April 6th, 2010, 03:39 PM
By Rgarbarino in forum General Archery Discussion
Last Post: June 23rd, 2008, 12:56 AM
By Milkman in forum General Archery Discussion
Last Post: January 24th, 2007, 06:32 PM
By TravisinWV in forum Bow Tuning
Last Post: December 17th, 2006, 08:36 PM
By Mike MT in forum General Archery Discussion
Last Post: December 5th, 2003, 04:00 AM