Archery Talk Forum banner
1-14 of 14 Results
  1. Bowhunting and Bowhunter Showcases
    Anyone here use the binocular/tripod adapter from Outdoorsmans? I'm specifically trying to figure out if it natively fits arca-swiss style tripod heads/clamps (without needing a plate) I see Bushnell released their new version that uses a similar stud setup - but theirs only mounts to a tripod...
  2. F.I.T.A. Classified
    I am selling 3 sets of early versions of my ILF to Formula adapters. They allow you to use any ILF limb with any formula riser. Every set has been tested to work, but there are a few minor flaws. They are overly strong and securely attach to the limb. They have been designed by me and have been...
  3. General Archery Discussion
    Hey please help... I'm looking for dimensions of the newest version (G2)of the Bowmaster split limb brackets. For both the wide version (1 1/8") and the standard (3/4") I just need: *The total outside width of the rubber coated fingers* *The size of the slot between the two rubber coated...
  4. F.I.T.A. Classified
    Set of super smooth Uukha X0 Evo2s, 36# mediums, I'd like to either sell or trade for equivalent formula limbs. The X0s were bought new a few months ago and have about 1100 arrows through them. They're in very good condition with some cosmetic scuffs to the clear coat on the limb pockets and...
  5. General Archery Discussion
    I have a spot hogg sight 5 pin sight head. It is not wrapped and it does not have a place to screw in the typical light. I have seen pictures of an adapter which screws into the holes on the back of the housing and holds the light. Does anyone know where I can get one of these holders or what it...
  6. General Archery Discussion
    Hey guys, been searching last couple days for some ILF adapter plates to throw on my Martin Jaguar, but every post of every forum I was on was from 2010 - 2012 and have not been able to find anything more recent. I don't suppose anybody on here would be able to point me in the direction of...
  7. General Archery Discussion
    High all. I recently purchased a like new Hoyt Reflex Grizzly and the rest that I purchased for it will not fit correctly. I searched the forums for information regarding the "filler plate adapter" and couldn't find an answer to my question... It appears that NAP makes a "QUIKTUNE ADAPTER PLATE...
  8. Want to buy or trade? WTB or WTT.
    I'm looking for the mathews arrow web quiver adapter to fit my hoyt bow. I called a bunch of mathews dealers and have searched everywhere and I am having zero luck finding one.. Hopefully someone out there has one they are willing to sell. Thanks!
  9. Want to buy or trade? WTB or WTT.
    Looking for the factory adapter for a Mathews Heli-M. [email protected]
  10. F.I.T.A. Classified
    Listed is a pair of Uukha ILF Carbon EX1 recurve limbs. They are 38 pounds but do not feel like it when you pull them at full draw. I have a 29" DL and these limbs generate 215 fps arrow speed. Extremely smooth, fast and has no torsional twist. I've used them on my Formula RX and PSE...
  11. DIY Equipment So i am going off of this thread withone exception. I want to be able to use this press to swap out limbs as well on my parallel limb Elite. So because i dont believe you can do this with the bowmaster adapter i have...
  12. Optics and Electronics
    I have a used Swarovski tripod adapter for the SLC Binoculars including the post that attaches to binoculars $100 Shipped. I accept Paypal.
  13. Misc. Items Only Want to Buy or Trade? WTB or WTT
    I recently purchased a used Mathews T3 Quiver and it is missing the Adapter/Mounting piece. I have the Quiver and Spider Claw. Message if you got one or know where I can get a replacement. I believe they come 1", 1-1/4", 1-1/2" Any help is appreciated!
  14. General Archery Discussion
    Help! Need a 7/16th-20 Bow Sight Light Adapter... Can use it if you got it, Please!
1-14 of 14 Results