I just built some 5mm, 250 spine FMJ's. The VPA footers I ordered were wayyy too big, so I pulled out the calipers and measured the OD of the arrow shaft and ID of the footer. Turns out the arrow shafts are 0.267 OD, but they're listed as 0.290 OD in Easton's chart. Has anyone else...
13 EASTON FMJ 400 SPINE 10.3 GP1 ARROWS, HIIT INSERTS INSTALLED. SOME ARE MISSING NOCKS/FLETCHINGS. ALL OTHERS FLETCHED ARE QUICK FLETCH THREE INCH FLETCHINGS. NO BENDS OR STRUCTURAL DAMAGE.
$100.00 TYD-PAYPAL PREFERRED
7- 4mm fmj injextions with easton titanium outserts and field points. 100gr. 28.5" 330 spine. Originally I had two dozen of these. And only shot 3. Sold all but these seven. I know one of these has been shot. I can tell it's scuffed. I dont think the rest have been. At least 5 new arrows here...
17 Easton 340 FMJ arrows.
Cut to 26.5” with inserts installed and misc nocks. 3 w/luminocks.
A few never shot, a couple have been through a deer. All will have all vanes attached.
$75 OBO + Shipping
I have 6 fmj injexion 330 spine. Practice shot them one time for about 30 minutes. They have Easton Titanium outserts. Fletched 2" blazer. 27.75"carbon 2 inside nock. 1 inch outsert. Total 28.75". Fletched. 120$ tyd.
2- aftermath 400 spine cut to 28.5" c 2 inside nock.
2- 5MM AXIS 340...
6- FMJ 4mm injections 330 spine. With Easton titanium outserts. Fletched never shot. Fletched in hot pink or red white and blue. I only have 4 of the hot pink 4 fletch. Or 3 blazer vanes
27.5" carbon to carbon or 28 3/8 from carbon to end of outsert.
145$ TYD. Paypal
The pic of the red white...
For sale is 10 Easton FMJ 340 arrows Nock-On edition - These arrows are uncut and the components are uninstalled.
The arrows come with 10 X nocks 10, 50/75 brass inserts a hit tool, and BAR rings -
PM with any questions. Thanks everyone!
I'm just starting to gather all of the gear I need for building my own arrows.
I picked up a Bitzenburger Jig from Nock On. I was considering sticking with the arrows I have rather than using the Nock On specific arrows.
All of the Nock On arrows are 6MM with an Outside Diameter of .267. The...
I have 6 FMJ Injexion 330 spine arrows for sale. They are fletched with the included blazer vanes and have the HIT inserts with deep six field points. They measure 28 7/8's from insert to nock throat. Only reason for sale is due to draw length change. Only 3 of the arrows have been shot, and...
So recently I took my bow to the shop to have it completely tuned, as I am new to archery. However, I had my arrows cut when I purchased them and had the HIT inserts glued. When I got my bow back, I was told my arrows are too long. Is there any possible way to fix this or do I have to buy new...
I'm selling 1 dozen Easton 5MM FMJ 340s because I'm not going to use them. I've had them for over a year and still haven't even glued the inserts in yet. They are cut already at 29" from the groove in the nock to end of shaft. The inserts I have are the Easton HIT inserts 50-75 grain break-offs...
I have 9 arrows in total. They have not been shot very much at all so in very good condition. These arrows measure 27 1/8" from insert to valley of the nock where it touches bowstring. The arrow is 27 3/8" overall.
HP inserts are installed and has black X Nocks with collars. These arrows are...
Selling the following arrows, please reference the item # when you message me about the arrows.
#1 - Carbon Express Maxima RED 350s - 9 arrows, fletched, all in good condition. $60 Shipped
#2 - Carbon Express PileDriver Extreme 350s - 10 arrows, fletch and in good condition - $55 Shipped