Search Results for ‘timing’

I have a mathews triax with the bottom cable alignment hole dead on and the top alignment hole slightly off. But heres the kicker. Both stops are hitting at the same time and ive bare shaft tuned the bow out to 20yrds and its shooting bullets! Should I adjust the cable and start all over or...

Hi all, I'm looking for an iPad based app that we can use for our club timing system. Our old gen 2 iPad has the "240 - Archery Timer" app on it (by Mario Strelec - link for what it looked like is here 240 - Archery Timer by Mario Strelec), but that seems to had been killed off many years ago...

Got a nexus 6 in today and noticed it is extremely out of time. when you lay the bow on a table and put the string on each outside cam timing Mark on the top and bottom cam, both inside marks are on the string side by roughly the same amount. In other words, the cams are “leaning forward” if...

Can someone confirm if the Black5 has static timing marks on the cams - like the Centergy? I looked the cams over and don’t see any, but my older eyes maybe missing them…. at least I can still see them on my Centergy.

Good afternoon guys, Currently shooting a VXR 31.5 ; just swapped out some strings and Everything is looking correct. 29.5 draw, peaks at 69.8 lbs and holds at 10.6 with 85% let off mods; timing is spot on. ATA is 31.7" and brace is 6" Question : Is it normal for the timing holes to be off...

I have a Realm SR6 that i just installed new strings and cables on. I have the limb bolts all the way turned in and have bow set at 32 1/16" ATA and a 6" brace height. The string is running in the center of the cam timing dots at rest. I ordered a LCA draw board for my press and it will be here...

I got tired of paying people to install strings,peeps,cables and any other things that requires a press. I bought a LCA press last week and was trying to find a chart that tells you when to add twist or take out twist. I remember a few years ago seeing a chart with pictures that explained...

Can't seem to get the arrow to clear the rest. Putting it on a BTX, only about 50lbs and 27" draw. I've tried a few different things to no avail. I work in an archery shop and have set up countless bows, but I can't bust this issue...anyone experience this? Any advice?

NOTE: For those that don't believe in paper tuning, I'm not going to argue with you. Find a paper tuning thread to make your argument against paper tuning. This thread is for those that want to paper tune their X-Force GX. I've collected a few PSE XF GX's over the years when I found a bow or...

I only recently received a My 2018 Martin Axon 36. I am having a hard time finding information on timing and tuning. The manual does not show any timing marks or anything. The only information I got was to set everything to center and paper tune, and then advance the cable to 2-3 twists...

I increased my DL to 31' on my Experience last night (apparently I've been collapsing my left shoulder this whole time) and the draw cycle is absolutely brutal. The hump to get into the valley is double what it was before and there is basically no valley. It also feels as if the let off is down...

I recently purchased an Infinite Edge from Dick's (I know, I know... first mistake). First it was setup completely wrong for me (mods set on different numbers), and this resulted in fraying of the cable that wraps around my top cam. I went to Fin Feather Fur, and got the timing right and he...

Hey All, I'm mystified by this one, and I'm turning to the community for help. I shoot a matthews conquest 2 lefty at 60 pounds at 32" draw (I'm tall w/ long arms). Shooting 125 gr. field points, on 300 spine arrows, w/ 4" helical vanetec v max vanes. I practice to 60 yards, and hunt to 30...

I need some help guys! I have a 2015 Obsession Phoenix, 60 lb limbs, 28.5" DL. I'm trying to learn how to tune my own equipment and this is my first attempt. I have the cams SYNCED to where both cable stops are contacting the cables at exactly the same time. My question is...How do I know when I...

I got my son a nuclear ice when he was six. He is now eight and the draw length is way too short. I was going to adjust the draw length and noticed that the cable did not line up with any of the timing dots. It is closest to the '1' dot. The manual does not provide any information on the...

Hello, I have a problem, maybe. I have a older 2004 Hoyt Razortec which I put some new strings on. They are all in spec or at least very close. I have no experience with the cam and a half systems and am not sure if they should feel the way this one feels. When I draw the bow it hits a solid...

Hi, I've been out of archery for 10+ years and boy have things changed!!!! I was fortunate enough to try a few bows and liked the Carbon Overdrive and am now setting up my rest and sight. So my question, is what do I need to do to make sure the setup of the bow is optimized to make sure...

Ok let me start by stating that I am an amateur to say the least. However I got my Creed to perfect 30 inch aa. perfect 7 inch brace, perfect 29 inch draw. However when I have it this way my cam sight hole is off the cable towards the riser. If I twist the cable to get it more in center then...

I have a QAD that just does not seem to be working right....It was tearing the fletchings off my arrows so I decided to just get the quickfletch shrink wraps as a quick fix to get the rest going right...well i feel like its pretty close but those two white lines that are supposed to line up are...

Hi, Wondering if any one has plans for or has built a Timing and Light system.Would like to build one for our clubs indoor league shoots and club nights.