Archery Talk Forum banner

Hoyt guys, I need some help

820 8
Ok A friend of mine just had his string break. He has a hoyt defiant He thinks it's a 1995 model. I need string length, cable length, ata, and brace hieght. ow ya it's a 60 to 70 lb bow with a 30 inch draw. Thanks
1 - 9 of 9 Posts

· Registered
Joined
·
1,663 Posts
Can probrably have them for you tomorrow, my string chart for Hoyts is at my buddies shop. I tried looking on Hoyt's sight but they only go to 1997. There is a Defiant listed in the 2000 models but my computer messed up and I don't have Adobe on it yet so couldn't view it. I'll post tomorrow.
 

· Registered
Joined
·
14,546 Posts
for a bow thats not on hoyts tune charts i would just give their 800 number a quick call and get exactly what you need for specs
 

· Registered
Joined
·
1,663 Posts
Didn't make it in to my buddies shop today but asked him over the phone, here goes.
First there are many combos depending on the cam and limb type. I'll try to list it as he said it, I'll list cam # for 30" draw (make sure to add 6" onto the cable length as I'm assuming it has a soft yoke).
command cam (C5) 57 1/2" string and 36 1/2" cables ATA 39 1/2" BH 7 1/4"
master cam (M3E) 58" string and 39 1/2cables. ATA 40" BH 7 1/4"
Supreme (E9) 62" string and 39 1/2" cables. ATA 42 1/2" BH 7"
Supreme command cam (C4) 58 1/2" and 38 1/2". ATA 41 1/2" BH 7 1/2"
Supreme master cam (M3D) 60 1/2" 38 1/2" cables. ATA 41 1/2" BH 7 1/2"
Supreme XL (M3E) 58" 36 1/2" cables. ATA 39 1/2" BH 7 1/2"
Heat command cam (C5) 57 1/2" 37 1/2" cables. ATA 40" BH 7 1/2"

Remember IF there is a soft yoke it is usually 12" long so folded in 1/2 gives you an extra 6" onto each cable length. Usually you can roughly measure it and determine which one it may be (also look at the cam and see which letter/number matches up).
Good luck.
 

· Registered
Joined
·
1,663 Posts
IroquoisArcher I have a '95 Hoyt Defiant with FastFlite limbs an A2 cams. Do you have the specs for this set up?? XMan01!
Sorry,hardly ever on. A2? The 1995 Defiant FastFlite I'm seeing for the E (energy wheel) for an E2 as 24" draw, 52.5"/36.5". Command cam (C2) as 28" draw, 55"/36.5"...both of these are ata 39.5" and bh 7.25". A MaserCam (M2C) shows 27" draw 55.5/36.5 with ata 40" and bh 7.25. I know these aren't the A2 but I don't see an A (advancecam) till later ( Defiant series posted before). You could try going to Hoyt's site and there is a Support section then scroll to Downloads and select View Tune Charts. Then drop down showing year and models. Hope this helped.
Sorry, see they only go back to 1997.
Sorry again. Searched and found this.
 
1 - 9 of 9 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top