Module Chart

Hope this helps everyone out

 

Thanks to TANC For posting link

Allegiance should have 6 dots showing outside the limbs

This was the same response I got from Bowtech when I asked about my 06 Allegiance They said you should always have the same amount of dots on both cams unless you are using a drop away rest tied to the cables.

As always, check axle to axle and brace to ensure these are correct and letoff should be correct.

I was told 5 dots should be showing on my 30" draw 06 Allegiance by Pat at Bowtech.

 

I was told 6 for best performance by several people and my Allegiance was 6 now keep in mind all this should be checked with limbs bottomed out

 

My tribute only has one dot, straight from Crackers.

Each bow will be a little different, but those are some good starting points.

 

My tribute only has one dot, straight from Crackers.

Each bow will be a little different, but those are some good starting points.

Is this at max draw weight

 

Yes.

 

For the OG at 28", what does draw stop setting of 5.4 mean?

 

I believe it means you are at 80% letoff.

TANC

 

I believe it means you are at 80% letoff.

TANC

Does that mean your draw stop peg should be 5.4 marks from the end setting (i.e. at the base of the cam)?

 

5.4 from top of cam every long mark is 1.0 every short line is 0.5

 

Is this at max draw weight

Yes.

 

Equalizer timing...

Heres some pics of my cam alignment on my Equalizer. These were taken as soon as I got the bow from Crackers.

Top Cam:

Bottom Cam:

 

Ttt

 

Eugene,
How many dots do you have showing ?
312 out of a 27.5" .....wow..... What arrows and any other info you can spare would be appreciated.
I will be getting mine set up next week. I cant wait.
Thanks, Jeff

 

Eugene,
How many dots do you have showing ?
312 out of a 27.5" .....wow..... What arrows and any other info you can spare would be appreciated.
I will be getting mine set up next week. I cant wait.
Thanks, Jeff

6 dots showing outside the limbs
Shooting 25 inch pse 200 with 100 grain field tip with a weight oh 309 which is 16 grain lighter then recomend but should be fine been shooting the same arrows in my mighty mite for 3 years with no problems

 

Constitution should have all dots showing outside the limbs AND the limb cutting the tooling hole in half outside the limbs

What is the tooling hole? Anyone got a pic of their Con's cams?

 

My Constitution's limb is only about a 1/4 though the tooling hole does this make any diffrence?

 

ttt

 

Tribute...

Mine has one showing outside each limb and I have a dropaway rest...still shooting bullet holes at 3 feet. They've also been flying great out to 45yds.

 

Draw stop hash marks...

Where on the draw stop peg should the marks be aligned?

Dead center?

 

Where on the draw stop peg should the marks be aligned?

Dead center?

Yes

 

Ttt

 

Draw stop peg and letoff??

I just got my 06 70/30 Allegiance yesterday and out the box it has 5 dots showing. Now I didn't put it on the scale but it doesn't seem to be getting a full 80% letoff, so my question is were should the draw stop peg be positioned as far as line slashes go? By the way B/C says 330.:wink: Would less letoff make it faster?

 

You should have mod 1 and it should be on the second big mark for 30 inch draw {The short marks are half marks as in 2.5}

I just got my 06 70/30 Allegiance yesterday and out the box it has 5 dots showing "By the way B/C says 330"

Your String needs to have some twist add to give you 6 dots showing with only 5 showing your draw is more then 30 inchs

 

Thanks eugene1e

Thank you I'll take a look at it tomorrow.